#########################              Config file parsing routine written by
#- Modplay Config file -#              Paul Sutton (P.C.Sutton@bradford.ac.uk)
#########################

# The Modplay config file must be called      Modplay.cfg
# If no file matching modplay.cfg is found in the current directory when
# you run MP then modplay will look at the directory in which the copy of
# mp.com being run is in (So if you put mp.com in c:\bin put modplay.cfg
# in there as well).
#
# All commands must be in lower case (that includes hex digits like 0ff2)
# Where a number is required the default is decimal unless preceeded by a $

# Lines preceeded by '#' are comments.  Remove the # from a command to
# make it active

# Colours may be
# Black Blue Green Cyan Red Magenta Yellow Gray
# Any of the colours can be preceeded by  light  or  flashing
# i.e. 	flashing red on blue, green,  black on yellow,
#	flashing light red on blue  etc.

##############################################################################
#
#    Mixing Speed - 6000 (6kHz) to 30000 (30kHz)
#    16kHz is normal for a 286 12Mhz + and not much is to be gained
#    by going higher
#
#    8Mhz     - use 6000 for a mixing speed and it will just work!
#   10Mhz     - try around 10000
#   12Mhz     - try around 15000
#   Better    - 15909 is Ok, or 22000 for bit better quality

mixing-speed 	15909	# 15909 normal mixing speed

##############################################################################
#
#    Mixing Speed - 6000 (6kHz) to 30000 (30kHz)
#    When running a shell to DOS.  If commented out then Modplay
#    just does 6kHz less than the mixing_speed above.  Lower this if Modplay
#    struggles when you shell to DOS
#

shell-mixing-speed 10000	# 10000 normal

##############################################################################
#
#   Default Output Device - the one Modplay starts up with.  If you select
#   a device that isn't available then Modplay will choose the next avaiable
#   one.   Output devices are from the list:
#
#   speaker    					PC Internal Speaker
#   lpt1     lpt2      lpt3      		D/A on parallel ports
#   disney1  disney2   disney3                  Disney sound source on LPT
#   lpts     					Stereo on 1&2
#   lptm     					Mono on 1&2
#   asm						Assembler routine (see below)
#   blaster					Sound Blaster
#   ston1					Stereo-on-1 board
#   user-mono					User defined mono
#   user-stereo					User defined stereo
#   user-quad					User defined quadrophonic

output-device   	speaker

##############################################################################
#
#   Protracker mode - If set to on then old mods (like Run The Gauntlet) will
#   sound better, but the protracker mods will then sound wrong.
#

protracker	off

##############################################################################
#
#     Default .GIF filename for background screen
#     (otherwise assumes .\MODPLAY.GIF)
#

#gif-filename	c:\gif\mwc\kelly.gif

##############################################################################
#
#    Spectrum Analyser Colour
#

#spectrum-colour         blue on black       # flashing light green on blue

##############################################################################
#
#    Specturm Analyser Character
#

#spectrum-bar-char       Ü

##############################################################################
#
#    Spectrum Analyser - Colour of end of bar
#

#spectrum-end-colour     red on black           # flashing red on black

##############################################################################
#
#   Bar LED colour
#

#bar-colour              black on blue

##############################################################################
#
#   Bar LED character
#

#bar-character           =

##############################################################################
#
#   Ignore Archives - If yes then don't look for MOD files in ZOO ZIP etc.
#

ignore-archives         no

##############################################################################
#
#   User Defined D/A mono port.  Use instead of -xm
#

#defined-mono            $022f

##############################################################################
#
#   User Defined D/A stereo port.  Use instead of -xs
#

#defined-stereo-l	$0300
#defined-stereo-r	$0301

##############################################################################
#
#   User Defined D/A quadrophonic port.  Use instead of -xq
#

#defined-quad-1		$030c
#defined-quad-2		$030d
#defined-quad-3		$030e
#defined-quad-4		$030f

##############################################################################
#
#   Playback display - the default display when playing a MOD
#   Can be one of:  blobs   spectrum   scroll  vga-scope  none
#

playback-display    	vga-scope

##############################################################################
#
# What order should Modplay present the directories and mods?  For each
# type of file give a priority.  Default is
# 1 0 3 1 1 1 1 1 1 1 2 meaning that
# directories first
# then (mod/lha/arj/zoo) sorted by filename
# then GIF
# then drives.
# 0 0 0 0 0 0 0 0 0 0 0 would give equal priority to all (try it!)
# (?) not used.
#                 MOD DIRs DRIVE ZIP LHA ARJ ZOO (?) (?) (?) GIF

#  sort-priority    1   0    3     1   1   1   1    1   1   1  2

##############################################################################
#
#    Make your own assembler code for driving your own hardware
#
#    A name for the defined output device - maximum 21 characters - no spaces
#    allowed :-(  [defining a name here enables the asm code given later]
#

#asm-name Pro-Gold-Whatsit+

#
#    Actual machine code for stereo playback to the output device.   Samples
#    are given in signed format in AL (left) and AH (right).  First convert
#    to unsigned format before outputing (something like  SUB AL,80, SUB AH,80)
#    You can use registers  AX  DX  BX  only and any relative jumps you
#    might need.  All numbers must be in hexidecimal and you have a maximum
#    of forty bytes. (Dont forget to remove the #'s!)

#asm ba 01 03         # mov dx,0300
#asm 2c 80            # sub al,080 - convert to signed
#asm ee               # out dx,al
#asm ba 2f 02         # mov dx,022f
#asm 88 e0            # mov al,ah
#asm 2c 80            # sub al,080 - convert to signed
#asm ee               # out dx,al